How to Build a Pergola Roof | Ep. 174


Pergola with no roof over patio.
You can use your outdoor house even when it’s raining by introducing a roof to a pergola.

A pergola roof guards you from pop-up storms, so you can increase your time outdoor.

Tyler Schwall in Mobile, Ala., wishes to set up a tin roof above his pergola. But before he does this, he wants to know the ideal way to set the roof so it has a pitch for rainwater.

Initially, buy some strain-treated 2-by-4s to cover just about every slat on the pergola. Make positive these boards are the exact size as the ones on the pergola.

Then, rip each and every 2-by-4 at a slight angle from its comprehensive width down to practically nothing. Ripping a board indicates chopping it alongside its size. This will make a tapered strip. Make absolutely sure the pitch of the roof is at minimum two inches so the rain will adequately move off of it.

Next, use some building adhesive on the slats and position the ripped boards on leading of them. This will include some extra waterproofing defense and maintain them secure when you’re putting in the tin roof.

Soon after you’ve placed the ripped boards on the pergola, protected them with wood screws. To continue to keep the tin roof from sagging, lay some 2-by-4s perpendicular to all those. 

Once all the boards are protected, install the tin roof. 

Now, you can sit exterior beneath your protected pergola and appreciate the audio of the rain dancing on the tin roof. 

Skip to [21:58] for the entire segment on the Today’s House owner Podcast.

Also in this episode:


Very best New Merchandise

 Two dogs run on Lifeproof with Petproof Technology Premium Pet Turf Irrespective of whether you want to secure your garden from animals digging or produce a place for them to roam, Lifeproof Premium Pet Turf has you lined. Find out more>> 

Very simple Alternatives

Finger twisting a bolt into the bottom of a wooden leg on patio furniture
This Straightforward Solution amounts patio home furniture and can help prevent wood rot.

Leveling Wooden Patio Furniture — Start out by dull a 3/8-inch diameter hole into the bottom of each and every desk or bench leg.

Then, use a hammer to tap a T-nut into every hole.

Thread a hex-head device bolt into just about every T-nut.

The bolts lift the bench off the patio to reduce rot, and they are adjustable to make certain the bench is stage. 

Watch: Tip for Leveling Wooden Patio Furniture  


A hacksaw cutting a bolt in a drill
If you need to minimize a bolt to sizing, allow a cordless drill do most of the get the job done for you.

Cleanse-Slice Bolts — Here’s how to shorten a machine bolt — threaded rod or carriage bolt — devoid of messing up the threads.

First, thread two hex nuts onto the bolt, then make the cut working with a hacksaw or jigsaw with a steel-slicing blade.

Then, spin off the nuts, just one at a time, making use of a wrench if important.

When the nuts occur off the conclude of the bolt, they’ll re-lower and straighten out any threads that had been damaged by the saw, creating it simple to thread the nut back on.  

Look at: Tip for Reducing Bolts to Size 


Engineered wood flooring with tools needed for installing.
Engineered wood flooring dramatically variations the glimpse of the area, but you have to have the appropriate plank sizing ahead of you start out. (digidreamgrafix, Getty Photos)

Issue of the Week

Q: I just acquired my initial home and I’m about to set up some engineered wood flooring.

In accordance to the set up recommendations, the past row of flooring need to not be much less than fifty percent the width of the planks. (The planks are five inches broad.) But the guidance never explain to you how to decide the width of the very last row.

Can you be sure to notify me how to determine that out? 

A: When setting up flooring, the first layout is heading to determine the good results of the task. Do not start off with a total-width plank and hope the last row is large plenty of. 

1st, measure the width of the home and divide by 5, the width of the plank. That will give you the quantity of comprehensive-width planks as well as any fractions.

If the past row is considerably less than 2½  inches, cut down the width of the 1st plank. 

Skip to [36:22] for the entire phase on the Today’s Property owner Podcast.



Further Reading through


Ask a Query! (Podcast)

Ask a question and we could response it on the “Today’s Homeowner Podcast!” We also may use it on our nationally syndicated radio broadcast or on todayshomeowner.com.



Supply url